Keeping Osoyoos Riding, One Bike at a Time.

At Rover Bike Shop Osoyoos, we're dedicated to keeping you riding safely, comfortably, and confidently. Whether you need a quick flat repair, a complete tune-up, e-bike diagnostics, or expert maintenance, our experienced technicians provide reliable service with attention to detail. Conveniently located in the heart of Osoyoos, we proudly serve local riders, commuters, and visitors exploring the South Okanagan's beautiful roads, trails, and vineyards. From everyday maintenance to advanced e-bike repairs, we're here to help you get the most out of every ride.

Expert Service. More Miles. Less Worry.

Bike Tuning, Service and Repairs in OSOYOOS

☐ Basic bike clean
☐ Align brake calipers
☐ Adjust shifting (front & rear)
☐ Torque all frame bolts
☐ Tighten seat rails
☐ Inspect cables & housings – document in work order
☐ Check chain wear – document in work order
☐ Inflate tires
Additional Safety Checks
☐ Inspect tires for wear and damage
☐ Inspect brake pads for wear
☐ Check wheel bearings for play
☐ Inspect headset for looseness
☐ Check bottom bracket for play
☐ Test ride bicycle
☐ Document additional recommendations in work order
E-BIKE ADD-ON (+$25)
☐ Test assist levels
☐ Test throttle (if applicable)
☐ Check display & accessories
☐ Inspect electrical system
☐ Check battery mounting and connections
☐ Test lights and electrical accessories
Includes everything in the Green Tune-Up, plus:
☐ All Green Tune-Up Service
☐ True wheels (front and rear)
☐ Top up tubeless sealant (if applicable)
☐ Brake bleed (includes mineral oil)
☐ Additional fluid bleed (+$3/oz)
☐ Full polish (Bike Protect / silicone spray)
E-BIKE ADD-ON (+$25)
☐ Disconnect all electrical connections
☐ Clean and re-seat connections
☐ Check display & accessories
Includes all Green & Blue Tune-Up Services, plus:
Drive Train & Components
☐ Remove pedals – apply copper compound
☐ Remove cranks – grease spindle & threads
☐ Remove bottom bracket bearings (threaded) – grease threads
☐ Remove chain – ultrasonic clean (replace if necessary – parts extra)
☐ Remove cassette – ultrasonic clean (replace if necessary – parts extra)
Frame & Finish
☐ Deep clean frame & wheels
☐ Polish (Bike Protect / Silicone Spray)
☐ Apply sweat protection
Cables & Brakes
☐ Replace all cables & housings (2 shift & 2 brake cables included)
☐ Hydraulic brake substitution rule: perform brake bleed instead of cable replacement
Note: Cables & housings are included. All other replacement parts are extra unless otherwise stated.
Braking System
☐ Measure rotors (replace if necessary – parts extra)
☐ Inspect brake pads (replace if necessary – parts extra)
Suspension Setup
☐ Set front suspension pressure (based on rider body weight)
☐ Set rear suspension pressure (based on rider body weight)
☐ Check and adjust suspension sag
E-BIKE ADD-ON (+$25)
☐ Remove motor cover (mid-drive only)
☐ Clean motor housing
☐ Inspect motor connections
☐ Apply anti-corrosion spray
☐ Reassemble motor cover
☐ Treat all electrical connections
FINAL SIGN-OFF
☐ Bike test ridden
☐ Shifting verified under load
☐ Braking verified under load
☐ No abnormal noise or play detected
☐ Final visual inspection completed
☐ Flat Repair ($20 + tube)
☐ Hub Motor E-Bike Flat Repair ($45 + tube)
☐ Brake Alignment ($20)
☐ Derailleur Adjustment ($25–$30)
☐ Tubeless Conversion ($35 + parts)
☐ Bike Inspection ($35)
☐ E-Scooter Repair ($30–$130)
A comprehensive safety and condition assessment including:
- Brake inspection
- Drivetrain inspection
- Tire and wheel inspection
- Frame and component check
- Written service recommendations
NEW BIKE / E-BIKE ASSEMBLY CHECKLIST
Assembly – Initial Setup
☐ Unbox bike carefully (inspect for shipping damage)
☐ Verify all parts present (hardware, pedals, reflectors, keys)
☐ Record serial number in system
☐ Install front wheel
☐ Install handlebars (correct orientation & torque to spec)
☐ Install seatpost & saddle (light grease or carbon paste as required)
☐ Install pedals (grease threads – correct L/R orientation)
Torque & Safety Check (Mandatory)
☐ Stem bolts torqued to spec
☐ Handlebar clamp torqued to spec
☐ Brake caliper bolts torqued
☐ Rotor bolts checked
☐ Crank bolts torqued
☐ Axles / QR properly secured
☐ Seatpost clamp torqued
Drivetrain Setup
☐ Rear derailleur aligned (hanger checked/straightened if required)
☐ Limit screws set (high & low)
☐ B-tension set correctly
☐ Shifting indexed (full range)
☐ Chain inspected for proper length
Braking System
☐ Braking calipers aligned
☐ Rotor trueness checked
☐ Brake lever feel tested
☐ Bed-in brakes (light test)
Wheels & Tires
☐ Wheels inspected for trueness
☐ Tire pressure set
☐ Tubeless system checked (if applicable)
☐ Axles tightened properly
E-BIKE SPECIFIC
☐ Battery installed and secured
☐ Battery charged (minimum 50%)
☐ Display powered on
☐ All assist levels tested
☐ Throttle tested (if applicable)
☐ Wiring inspected for damage/pinch points
☐ Charger included and verified
Final Build Details
☐ Accessories installed (kickstand, reflectors, etc.)
☐ Firmware / settings checked (if applicable)
☐ Suspension pressures set (base setup)
☐ All cables routed cleanly
☐ Cosmetic check (no scratches, marks, or residue)
Test Ride (Mandatory)
☐ Bike test ridden
☐ Shifting verified under load
☐ Braking verified under load
☐ No abnormal noises detected
☐ Steering aligned and straight
FINAL SIGN-OFF
☐ Bike test ridden
☐ Shifting verified under load
☐ Braking verified under load
☐ No abnormal noise or play
☐ Final visual inspection complete
NEW BIKE / E-BIKE ASSEMBLY CHECKLIST
Assembly – Initial Setup
☐ Unbox bike carefully (inspect for shipping damage)
☐ Verify all parts present (hardware, pedals, reflectors, keys)
☐ Record serial number in system
☐ Install front wheel
☐ Install handlebars (correct orientation & torque to spec)
☐ Install seatpost & saddle (light grease or carbon paste as required)
☐ Install pedals (grease threads – correct L/R orientation)
Torque & Safety Check (Mandatory)
☐ Stem bolts torqued to spec
☐ Handlebar clamp torqued to spec
☐ Brake caliper bolts torqued
☐ Rotor bolts checked
☐ Crank bolts torqued
☐ Axles / QR properly secured
☐ Seatpost clamp torqued
Drivetrain Setup
☐ Rear derailleur aligned (hanger checked/straightened if required)
☐ Limit screws set (high & low)
☐ B-tension set correctly
☐ Shifting indexed (full range)
☐ Chain inspected for proper length
Braking System
☐ Braking calipers aligned
☐ Rotor trueness checked
☐ Brake lever feel tested
☐ Bed-in brakes (light test)
Wheels & Tires
☐ Wheels inspected for trueness
☐ Tire pressure set
☐ Tubeless system checked (if applicable)
☐ Axles tightened properly
E-BIKE SPECIFIC
☐ Battery installed and secured
☐ Battery charged (minimum 50%)
☐ Display powered on
☐ All assist levels tested
☐ Throttle tested (if applicable)
☐ Wiring inspected for damage/pinch points
☐ Charger included and verified
Final Build Details
☐ Accessories installed (kickstand, reflectors, etc.)
☐ Firmware / settings checked (if applicable)
☐ Suspension pressures set (base setup)
☐ All cables routed cleanly
☐ Cosmetic check (no scratches, marks, or residue)
Test Ride (Mandatory)
☐ Bike test ridden
☐ Shifting verified under load
☐ Braking verified under load
☐ No abnormal noises detected
☐ Steering aligned and straight
FINAL SIGN-OFF
☐ Bike test ridden
☐ Shifting verified under load
☐ Braking verified under load
☐ No abnormal noise or play
☐ Final visual inspection complete